Gary need more information to offer any help. It’s almost impossible to guess at the problem with questions like this without very detailed information.
For you, and other users when problems arise, please provide:-
A detailed makeup of your system. Boards in the system, ideally, ports used.
Speed of the CPU, wait states used.
Monitor(s) version(s).
Type of S100 motherboard.
CPM/MSDOS versions being used
Source of BIOS(s)
History, what works, did the problem suddenly appear or it never worked.
Specifically in this case, “doesn’t change over time” . What does that mean. When you read all the registers with the diagnostic program over time, what values do you get when you dump the clock’s RAM.
Same values a minute later?
Are you sure no other board is using ports 70 & 71H.
Try a second DS chip. If you still have problems I will take a look at it for you
John
From: n8vem...@googlegroups.com [mailto:n8vem...@googlegroups.com] On Behalf Of geka...@gmail.com
Sent: Thursday, July 24, 2014 7:31 AM
To: n8vem...@googlegroups.com
Cc: mon...@vitasoft.org
Subject: Re: [N8VEM-S100:4686] MSDOS Support V2 PCB RTC problem.
I continue to have no luck with the RTC. Strange symptoms...
I can set the clock with the CP/M Z-RTC program, but it doesn't change over time.
I can set the clock with the 8088 monitor V10.32 "E" command and only the seconds and day portions will change.
I've swapped out the battery, xtal, DS12885+, and support IC's.
I've ordered a DS12887 to try, as that should eliminate the xtal and battery as issues.
The rest of the board (Eprom access, Interrupt controller, Timer) work fine. I still haven't tested the Keyboard controller section.
I'm almost ready to just build up a second board. Any ideas or suggested troubleshooting procedures?
- Gary
On Thursday, July 17, 2014 10:03:16 AM UTC-4, gek...@gmail.com wrote:
John -
Crystal should be here in a few days, finger's crossed.
I'll also try simplifying the system tonight and using the Z-RTC program under CP/M3 instead of the 8088 board. I'll see if that makes any difference.
- Gary
On Thursday, July 17, 2014 12:36:10 AM UTC-4, monahanz wrote:
Gary, just rechecked mine (been a long time since I was there!). The clock seems fine for time and date. Was many months ago since I set it. The only thing I see an error with is the century (“20”) came up as ?? so it read as ??14/07/16
When I reset the date it appears OK i.e. as 2014/07/16. On reset and power down it comes back correctly as 2014. Not sure what the problem is/was.
Sorry don’t have a suggestion for you. Hope it is the crystal.
John
From: n8ve...@googlegroups.com [mailto:n8ve...@googlegroups.com] On Behalf Of gek...@gmail.com
Sent: Wednesday, July 16, 2014 11:37 AM
To: n8ve...@googlegroups.com
Subject: [N8VEM-S100:4612] MSDOS Support V2 PCB RTC problem.
I'm pulling out my hair trying to access the DS12885 RTC on the MSDOS Support PCB.
The rest of the board (timer, interrupt and EPROM) appears to be functioning properly. I have not tried the mouse/keyboard section yet.
I can see low pulses on Pins 14/17 as expected. I'm using the "E" command from the 8088 board for testing time/date in V10.3 of John's monitor software.
When I set the time the seconds and day will program, but the hours/minutes/year/month remain gibberish. I also get errors when entering the "X" MSDOS menu - either that the RTC is stuck or that invalid BCD data exists.
I've swapped TTL and DS12885. I've also changed the 32.768khz xtal. When I scope pins 2/3 on the DS12885 (XTAL) I can see somewhat noisy pulses.
Would the DS12885 at least store the date if the xtal isn't oscillating properly? It looks like the RTC shares most of the same address/data circuitry with the other sections. The 8088 has a 8 mhz clock, could speed be an issue?
Any thoughts or hints appreciated!
- Gary
--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.