Don, looks good, put me down for 2. Josh
Date: Tue, 9 Dec 2014 18:46:36 -0800
Subject: Re: [N8VEM-S100:5809] Re: NKK Switches for Mini FP
From: cap...@uxpro.com
To: n8vem...@googlegroups.com
So this is some good news. I sent my PCB bracket design to PCBCart for a quote.
Turns out we can do this brackets for $1.26 each, quantity 50 plus tooling ($20) and
shipping. So for $5.00 I could get everyone one bracket or better yet Qty 100 they drop
to $.84 cents and you can get two. This price is hard to beat. I don't think we can do any
--
--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
Date: Tue, 9 Dec 2014 18:46:36 -0800
Subject: Re: [N8VEM-S100:5809] Re: NKK Switches for Mini FP
From: cap...@uxpro.com
To: n8vem...@googlegroups.com
shipping. So for $5.00 I could get everyone one bracket or better yet Qty 100 they drop
to $.84 cents and you can get two. This price is hard to beat. I don't think we can do any
better. If go nuts, qty 200 are .58 cents!
On Tue, Dec 9, 2014 at 2:32 PM, Richard Cini <rich...@verizon.net> wrote:
I don't have my IMSAI a disassembled but that kind of bracket did it use?
Sent from my iPhoneof the board houses. I know my board house does these.I'm thinking it could be made from PCB material and we could have it done by onea soldering jig or a removable mounting bracket. It will involve more effort/expense.If we want a better bracket perhaps this would be a better design. It could be used aswhich would add more strain relief.chassis design. Two of these bars could be used for the top and bottom of the switchinch that can be use for mounting. You'll have to cut, trim and drill depending on yourMy modified design is basically just a flat bar 1/2 inch wide with tails that extend onethen was able to lift the bracket off from underneath the switches. Had the bracket beenI took Franks bracket which was made out of PCB material, cut a slot in one side andand thread into the bracket. So once the switches are soldered in the bracket can notThe bracket has to sit under the switch flange. Screws pass through the flangeThe bracket in the dxf drawing is great however I would consider it a permanent part.truly appreciate the effort.Frank did a great job on the bracket. He was kind enough to build a prototype andshipped to me complete with screws at his own expense. Thanks again Frank. I
be removed.
made out of steel or aluminum it would have gotten bent/distorted.
<SwitchBracketEnd.gif>
So what do ya think? Keep those suggestions coming.Thank you.On Tue, Dec 9, 2014 at 2:07 AM, Frank Schieschke <f.schi...@googlemail.com> wrote:Hello,
see also this thread.
For one that is interesting by building it by yourself, i provide the DXF file attached.
Frank
--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
--
--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
--
--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.