No problem “molesting my layout” Don. I consider all these boards “public domain”.
There are a lot of lines to reroute. Not sure quite which would be the best way. You should try and keep the 0.1” spacing for header pins. So either between each trace, or a few rows in the middle of the board with traces around the sides.
I also have a custom board I picked up where somebody allowed you to as well place a connector horizontally so you can easily get to contacts on the back of a board. It’s slightly above the other boards and lays flat and points forward.
John
From: n8vem...@googlegroups.com [mailto:n8vem...@googlegroups.com] On Behalf Of Don Caprio
Sent: Thursday, January 29, 2015 10:17 AM
To: n8vem...@googlegroups.com
Subject: Re: [N8VEM-S100:6119] RFC - S100 Bus Test Point PCB
John, I would be happy to take that on. I considered it before but didn't
want to molest someone else's design.
On 01/29/15 09:54 AM, John Monahan wrote:
Agree, let’s keep it simple. Popping it on top of the current extender board makes sense. Someday perhaps I, you, or somebody else, could reroute the traces on the current extender board (http://s100computers.com/My%20System%20Pages/Extender%20Board/Extender%20Board.htm ) , to add this very useful feature.
John
From: n8vem...@googlegroups.com [mailto:n8vem...@googlegroups.com] On Behalf Of Don Caprio
Sent: Thursday, January 29, 2015 8:51 AM
To: n8vem...@googlegroups.com
Subject: Re: [N8VEM-S100:6113] RFC - S100 Bus Test Point PCB
Guys, Great feedback so far and some great suggestions. I was trying to keep it
simply but some of the suggested features sounds like must haves. The +5v
at a minimum.
I was thinking that it would be used in a second extender card so all the other features
like LED's, power etc come from another source. Second extender card would sit in
front of the first with break out board so keeping the height to a minimum was important.
Sorry for the bad pic. That was just a screen grab from Kicad. Here's a better pic from FreeDFM:
On Thu, Jan 29, 2015 at 8:27 AM, norwestrzh via N8VEM-S100 <n8vem...@googlegroups.com> wrote:
Hi Don --
This looks like a great idea!! I'd take two of them if you fab. them.
Roger--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
---------------------------------
Don Caprio cap...@uxpro.com
http://www.uxpro.com
(925) 240-UNIX--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
--
Don Caprio
ilv...@gmail.com
--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.