Re: [N8VEM-S100:5834] FP Mini Group NKK Switch Group

Re: [N8VEM-S100:5834] FP Mini Group NKK Switch Group - Complete

Subject: Re: [N8VEM-S100:5834] FP Mini Group NKK Switch Group - Complete

Date: Mon, 15 Dec 2014 07:57:23 -0800

Authentication-results: gmr-mx.google.com; spf=pass (google.com: domain of ilv...@gmail.com designates 2607:f8b0:400e:c02::22d as permitted sender) smtp.mail=ilv...@gmail.com; dkim=pass head...@gmail.com; dmarc=pass (p=NONE dis=NONE) header.from=gmail.com

Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20120113; h=message-id:date:from:user-agent:mime-version:to:subject:references :in-reply-to:content-type; bh=mjimRqRT3qcnj+olUAdz4opjcqxgRBuGfkNv+VjoUvY=; b=w6DaANtaBdzpj+dDLV65kQvXmOJWdSznR3Fw9wHKaVs8x3zOpRyLkukkuoDe4WGrnh PbXLUV18oc+GMIWArxiClq7KKbLPUAItbkjAY/JRSeqxgSDZ/6fiZ2HZQnWW4YQZDfwb ZayS2EWlUnb01zWnLbOUimRCsXECk1UZktQmnDdfFNtJW2MXb0mBwplHOflrh9mfwOeR VEKQmKaX2XRzvJk9SjRMAKfSk+IiH9xYA3Hry8/2pyVFsIe0NUKJpMnfVgGS48ZBc3vc yKfVLYpb70L8aNG7VGbUtJ31QB8muM4CicqrsECahNJE/lek3KDKxkUog0yLlBkWr8Al em5A==

In-reply-to: <CAJj77rsPV_2QgCD4GeKb+FKWcmjo053aYHV3VtJdYZH5PiVFsg@mail.gmail.com>

References: <CAJj77rsPV_2QgCD4GeKb+FKWcmjo053aYHV3VtJdYZH5PiVFsg@mail.gmail.com>

User-agent: Mozilla/5.0 (X11; SunOS i86pc; rv:17.0) Gecko/20140429 Thunderbird/17.0.11

It's on the N8VEM Wiki. Near the bottom of the Front page
there is a section for S-100 boards. Board 16 is the front panel.

http://n8vem-sbc.pbworks.com/w/browse/#view=ViewFolder&param=S-100%20FPMini

On 12/14/14 11:32 PM, Paul Birkel wrote:

Just color me dumb, Don. Where is the FP Mini Wiki that you mention?
On Thu, Dec 11, 2014 at 4:20 AM, Don Caprio <ilv...@gmail.com> wrote:
Attention FP Mini builders

...

If you've been watching the Wiki, I do regret that the RUN and HALT
LED's got swapped. You have two choices here. Change the silkscreen,
or wait for a fix. I attempted some jump and cut and borked my
board. Luckly I was able to restore and got it operational again. I do have
a fix that does not require cuts and jumpers. It's a bit cheesy so I'm
reluctant to share at this point. Basicaly involves placing tape over the
component holes and using the long LED leads to reach the proper holes.

I am planning on a V2 board. It will have the LED fix, all jumpers moved
to a dip switch on top of the board and line drivers for the S100 bus signals
which should allow the board to run better at higher speeds. It's going to be
tricky finding real estate for the extra components, but I'm up for the
challenge.

Thank you all for supporting this project.

...

-- Don Caprio ilv...@gmail.com
--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
--
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

-- 
Don Caprio
ilv...@gmail.com